Aug 10

The augers are also called the screw conveyors, they are used in GN drilling cuttings waste management system as a matching equipment alongside with vertical cuttings dryers and decanter centrifuges.
In some rig sites, it is requested by the law that for each drilling rig, there must be a set of drilling cuttings waste management system, and totally in the rig site, there should be at least 2 augers: first one is below the discharge chutes of shale shakers, desander cones and desilter cones, that is used to collect the cuttings. Second one is used as a sloping angle to transfer the cuttings from the first one to the vertical cuttings dryer. In a word, the augers could be positioned sloping or horizontal for different destinations. In a word, GNSC screw conveyors could work in a group or singly, and they could be used for mixing, allocating, dewatering, discharging and etc.

gn augers

As an essential part of a waste management system, in order to well match the other equipment and easy for transportation and locating, all GN screw conveyor models are designed in same length sections, each of 12 ft. And they are of different diameters for providing different transferring capacities. There are 10 inch diameters, 12 inch diameters, 14 inch diameters and 16 inch diameters. In this condition, most of spare parts are interchangeable, which reduced the spare parts cost and enhanced the convenience for the end users. GNSC series screw conveyors are using the wear proof material for a obviously longer service life than its peers’.
GNSC series screw conveyors are not only used in the drilling cuttings waste management systems, they are also quite widely used in construction, chemical, power plants, coal mining and other industries. In some customized conditions, GN could also add the insolation layer to the augers to keep the temperature at a certain range.
For more information, welcome to contact GN directly.

Share

written by shale shaker \\ tags: , , , ,

Jul 12

Just not long ago, GN Solids Control who owns are quite professional R&D team in solids control industry, has developed and got patented of a series of ViST Vacuum Shakers. It would be a new page of solids control industry, because the ViST vacuum shaker will greatly reduce the drilling cutting proportion and enhance the treating performance during solids control.
Here is the working video of GN ViST Vacuum Shaker.
Here are the main parameters of GN ViST vacuum shaker:
1. Pressure of air source: 0.7-1.0 Mpa, equal to 100 to 150 psi
2. Air consumption: 4.5 cbm/min, equal to 160CFM
3. Matching shaker quantity: 2 or 3 sets
4. Suitable mud: all types of mud including SBM, OBM and WBM
5. Mud recycling ratio: 30 to 50 percentage
6. Mud temperature from minus 15 degrees to 85 degrees centigrade
7. Control type: automatic pneumatic control
8. No electrical power needed

Features and advantages of GN ViST Vacuum Shaker:
1. Wide application for all mud type including WBM, OBM and SBM.
2. It is suitable for both land rigs and offshore rigs, to enhance the working efficiency of the shake shakers, to recycle the drilling fluid to the most while discharge the cuttings to the least.
3. A ViST shaker could replace the drying shaker at a lower cost comparing with drying shaker.
4. Small footprint, even no extra space needed when added onto existing shakers, which is very important for offshore conditions.
5. Easy for installation for both GN’s own shakers and other brands’ shakers.
6. By using a ViST devise, the solids control shale shaker can use shaker screens with larger API number without leaking, in order to enhance the treating efficiency.
7. By discharging dryer cuttings, it would be easier for transport or discharge the drilling cuttings.
8. Easy to be operated by one operator only.
For more information, welcome to contact GN Solids Control directly.

Share

written by shale shaker \\ tags: , , ,